Certshared
2017 Cisco Official New Released 200-125 ♥♥
100% Free Download! 100% Pass Guaranteed!
http://www.certshared.com/exam/200-125/


It is impossible to pass Cisco 200-125 exam without any help in the short term. Come to Pass4sure soon and find the most advanced, correct and guaranteed Cisco 200-125 practice questions. You will get a surprising result by our Replace CCNA Cisco Certified Network Associate CCNA (v3.0) practice guides.

2017 Mar 200-125 testing engine

Q131.  - (Topic 5)

Refer to the exhibit.

What is the most appropriate summarization for these routes?

A. 10.0.0.0 /21

B. 10.0.0.0 /22

C. 10.0.0.0 /23

D. 10.0.0.0 /24

Answer: B

Explanation:

The 10.0.0.0/22 subnet mask will include the 10.0.0.0, 10.0.1.0, 10.0.2.0, and 10.0.3.0 networks, and only those four networks.


Q132.  - (Topic 7)

An administrator is trying to ping and telnet from SwitchC to RouterC with the results shown below.

Click the console connected to RouterC and issue the appropriate commands to answer the questions.

What would be the effect of issuing the command ip access-group 115 in on the s0/0/1 interface?

A. No host could connect to RouterC through s0/0/1.

B. Telnet and ping would work but routing updates would fail.

C. FTP, FTP-DATA, echo, and www would work but telnet would fail.

D. Only traffic from the 10.4.4.0 network would pass through the interface.

Answer: A

Explanation:

First let’s see what was configured on interface S0/0/1:


Q133.  - (Topic 8)

Which component of the Cisco SDN solution serves as the centralized management system?

A. Cisco OpenDaylight

B. Cisco ACI

C. Cisco APIC

D. Cisco IWAN

Answer: B

Explanation:

Cisco ACI is a comprehensive SDN architecture. This policy-based automation solution supports a business-relevant application policy language, greater scalability through a distributed enforcement system, and greater network visibility. These benefits are achieved through the integration of physical and virtual environments under one policy model for networks, servers, storage, services, and security.


Q134.  - (Topic 5)

You have been asked to come up with a subnet mask that will allow all three web servers to be on the same network while providing the maximum number of subnets. Which network address and subnet mask meet this requirement?

A. 192.168.252.0 255.255.255.252

B. 192.168.252.8 255.255.255.248

C. 192.168.252.8 255.255.255.252

D. 192.168.252.16 255.255.255.240

E. 192.168.252.16 255.255.255.252

Answer: B

Explanation:

A subnet mask of 255.255.255.248 will allow for up to 6 hosts to reside in this network. A subnet mask of 255.255.255.252 will allow for only 2 usable IP addresses, since we cannot

use the network or broadcast address.


Q135.  - (Topic 3)

Refer to the graphic.

R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)

A. All of the routers need to be configured for backbone Area 1.

B. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.

C. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.

D. The hello and dead interval timers are not set to the same values on R1 and R3.

E. EIGRP is also configured on these routers with a lower administrative distance.

F. R1 and R3 are configured in different areas.

Answer: D,F

Explanation:

This question is to examine the conditions for OSPF to create neighborhood.

So as to make the two routers become neighbors, each router must be matched with the following items:

1. The area ID and its types;

2. Hello and failure time interval timer;

3. OSPF Password (Optional).


Replace 200-125 actual exam:

Q136. CORRECT TEXT - (Topic 7)

The following have already been configured on the router:

✑ The basic router configuration

✑ The appropriate interfaces have been configured for NAT inside and NAT outside.

✑ The appropriate static routes have also been configured (since the company will be a stub network, no routing protocol will be required)

✑ All passwords have been temporarily set to “cisco”.

The task is to complete the NAT configuration using all IP addresses assigned by the ISP to provide Internet access for the hosts in the Weaver LAN. Functionality can be tested by clicking on the host provided for testing.

Configuration information:

router name – Weaver

inside global addresses – 198.18.184.105 - 198.18.184.110/29 inside local addresses - 192.168.100.17 – 192.168.100.30/28 number of inside hosts – 14

A network associate is configuring a router for the weaver company to provide internet access. The ISP has provided the company six public IP addresses of 198.18.184.105 198.18.184.110. The company has 14 hosts that need to access the internet simultaneously. The hosts in the company LAN have been assigned private space addresses in the range of 192.168.100.17 – 192.168.100.30.

Answer: 

The company has 14 hosts that need to access the internet simultaneously but we just have 6 public IP addresses from 198.18.184.105 to 198.18.184.110/29. Therefore we have to use NAT overload (or PAT)

Double click on the Weaver router to open it

Router>enable Router#configure terminal

First you should change the router's name to Weaver

Router(config)#hostname Weaver

Create a NAT pool of global addresses to be allocated with their netmask. Weaver(config)#ip nat pool mypool 198.18.184.105 198.18.184.110 netmask 255.255.255.248

Create a standard access control list that permits the addresses that are to be translated.

Weaver(config)#access-list 1 permit 192.168.100.16 0.0.0.15

Establish dynamic source translation, specifying the access list that was defined in the prior step.

Weaver(config)#ip nat inside source list 1 pool mypool overload

This command translates all source addresses that pass access list 1, which means a source address from 192.168.100.17 to 192.168.100.30, into an address from the pool named mypool (the pool contains addresses from 198.18.184.105 to 198.18.184.110). Overload keyword allows to map multiple IP addresses to a single registered IP address (many-to-one) by using different ports.

The question said that appropriate interfaces have been configured for NAT inside and NAT outside statements.

This is how to configure the NAT inside and NAT outside, just for your understanding:

Weaver(config)#interface fa0/0 Weaver(config-if)#ip nat inside Weaver(config-if)#exit Weaver(config)#interface s0/0 Weaver(config-if)#ip nat outside Weaver(config-if)#end

Finally, we should save all your work with the following command:

Weaver#copy running-config startup-config

Check your configuration by going to "Host for testing" and type:

C :\\>ping 192.0.2.114

The ping should work well and you will be replied from 192.0.2.114


Q137.  - (Topic 8)

Which two statements about northbound and southbound APIs are true? (Choose two.)

A. Only southbound APIs allow program control of the network.

B. Only northbound APIs allow program control of the network.

C. Only southbound API interfaces use a Service Abstraction Layer.

D. Only northbound API interfaces use a Service Abstraction Layer.

E. Both northbound and southbound API interfaces use a Service Abstraction Layer.

F. Both northbound and southbound APIs allow program control of the network.

Answer: B,C


Q138.  - (Topic 6)

How does using the service password-encryption command on a router provide additional security?

A. by encrypting all passwords passing through the router

B. by encrypting passwords in the plain text configuration file

C. by requiring entry of encrypted passwords for access to the device

D. by configuring an MD5 encrypted key to be used by routing protocols to validate routing exchanges

E. by automatically suggesting encrypted passwords for use in configuring the router

Answer: B

Explanation:

By using this command, all the (current and future) passwords are encrypted. This command is primarily useful for keeping unauthorized individuals from viewing your password in your configuration file


Q139. .  - (Topic 3)

A Cisco router is booting and has just completed the POST process. It is now ready to find and load an IOS image. What function does the router perform next?

A. It checks the configuration register.

B. It attempts to boot from a TFTP server.

C. It loads the first image file in flash memory.

D. It inspects the configuration file in NVRAM for boot instructions.

Answer: A

Explanation:

Default (normal) Boot Sequence

Power on Router - Router does POST - Bootstrap starts IOS load - Check configuration register to see what mode the router should boot up in (usually 0x2102 to read startup- config in NVRAM / or 0x2142 to start in "setup-mode") - check the startup-config file in NVRAM for boot-system commands - load IOS from Flash.


Q140.  - (Topic 3)

What are two enhancements that OSPFv3 supports over OSPFv2? (Choose two.)

A. It requires the use of ARP.

B. It can support multiple IPv6 subnets on a single link.

C. It supports up to 2 instances of OSPFv3 over a common link.

D. It routes over links rather than over networks.

Answer: B,D